Water Heater Repair Denver is a job best left to professional technicians. They have the training and certification to complete the repair correctly and safely.

The first thing to check is if the pilot light has gone out. If it has, then it can be easily reignited by turning the gas back on.

A leaking water heater wastes gallons of water and can damage home exteriors, walls, and surfaces. This type of water damage is not something homeowners want to deal with. The longer the problem persists, the more expensive it will be to resolve. The good news is that with preventative measures, homeowners can help avoid water damage from a hot water heater.

A leak from the bottom of a water heater is often caused by sediment and mineral buildup corroding through the tank. In this case, the tank will need to be replaced. Leaks from the top are also common and could be caused by loose pipe connections. A plumber can tighten the pipes if necessary.

Pooling water around a water heater could be caused by a faulty temperature and pressure relief valve. This valve helps to reduce the pressure inside of the tank, but if it is faulty or damaged, it can leak. This valve can be easily fixed with a simple wrench, but if the entire device is faulty, it will need to be replaced.

If a puddle of water is present under a water heater, the most important thing to do is to shut off the water heater. This is a safety precaution, especially for gas water heaters that use natural gas. It is usually easy to do and is located on the side of the unit near the burner. Once it is shut off, it should remain off until a plumber can look at the unit and perform repairs.

If the puddle is from condensation, it may be necessary to turn off the gas or electricity to the water heater. This is another reason why it’s crucial to locate the unit and know how to shut it off in an emergency. Electric water heaters can be turned off using the circuit breaker box, while gas water heaters will need to have the gas or electricity switched off at the source. It is recommended that homeowners call in a professional when working with either type of water heater because they involve dangerous elements.

Faulty Thermocouple

If the pilot light on your water heater will not stay lit, you could have a problem with the thermocouple. This is a safety feature that is designed to detect the heat of the pilot flame and keep gas flowing into the water heater. If it senses no heat, it will shut off the gas flow to your home. While this keeps your home safe from gas leaks, it also means that you won’t have hot water until the problem is fixed.

The Thermocouple is a small, cylindrical piece of metal that sits near the pilot flame. It has two leads that are connected to the gas control valve. If the pilot light goes out, it will trigger the thermocouple to close the gas valve. Eventually, this will stop gas from flowing to your heater and your pilot light won’t be able to ignite.

There are several reasons why your Thermocouple might be faulty and it’s important to understand them all so that you know what to look for when the time comes to replace it. Thermocouples are extremely sensitive and can be damaged by soot build-up, a drop in voltage due to age or corrosion, or even simply being bent. If you suspect that your Thermocouple is faulty, it’s always best to call in the professionals rather than trying to repair or replace it yourself.

While it may seem like a simple fix, replacing the thermocouple is something that most people don’t attempt on their own. Because it involves working with gas that is highly flammable, you’re going to want to make sure that the job is done properly by someone who knows what they’re doing and can work safely around flammable gas.

First, you’ll need to shut off the gas supply to your water heater by turning the valve at the top of the tank to the ‘Off’ position. Next, you’ll need to remove the burner assembly and the thermocouple from the bottom of your water heater. Once you have the parts removed, you can slowly and firmly pull and twist the old thermocouple to remove it from its bracket. Then you can take it to your hardware or home improvement store and purchase an exact replacement for it.

Sluggish Performance

Having a water heater that isn’t functioning properly can be inconvenient and frustrating. But, even if it doesn’t seem to be working at all, a professional plumber can assess the situation to determine what’s going on and provide you with solutions that will fix your problems. Here are a few common issues that can arise:

Low water pressure:

If you have noticed that your shower is producing less water than usual, the cause could be due to a faulty thermostat or heating element. If this is the case, replacing the thermostat or element will help restore normal operation.

Hot water that runs out:

If your hot water seems to be running out after only a short amount of time, it may be due to a faulty thermocouple or a blown fuse. A professional plumber will be able to test the thermocouple and replace it if necessary.

Smelly or discolored water:

When your water begins to smell bad or turn discolored, it is likely because of a buildup in the water heater that needs to be removed by a professional. This will help to prevent further damage and ensure your water is clean and safe for use.

Noisy or leaking:

If you hear loud noises coming from your water heater, it’s important to contact a professional right away. This problem can indicate that your unit is nearing the end of its lifespan or is beginning to fail. Replacing your water heater may be the best option if it is approaching the end of its life span or if you have been experiencing frequent leaks.

Sluggish performance:

Sluggish performance of your water heater can be caused by a variety of problems. However, one of the most common is that your tank is too small for your household. Replacing your water heater with a larger one can improve the situation. It is also possible that your thermostat dial is set to a higher temperature than you need, which can lead to decreased performance. In this case, adjusting the thermostat to the proper temperature will resolve the issue.

Smelly Water

A home’s water should smell clean, not rotten eggs or sewage. However, unpleasant odors can occur in a variety of situations, from chemical reactions to elevated traces of minerals. While these problems may not be hazardous, they should be dealt with promptly to ensure your home’s plumbing is functioning properly.

A foul smell coming from the water heater is usually caused by anaerobic bacteria in the tank, which react with magnesium and aluminum anodes to produce hydrogen sulfide gas. This problem can be intensified if your water heater has been shut down for an extended period of time to save energy.

Sulfur or rotten egg odors can also be produced by sulfur-reducing bacteria that feed off soaps, decaying organic material in your drains, and/or other dissolved materials in the pipes and hot water tank. These odors are often pushed into the faucet when you turn on the hot water, and they can be more pungent if the water has a low chlorine residual or sulfates and/or is old.

Water odors can also be caused by elevated traces of minerals like mercury, lead, iron, zinc, manganese, and/or copper. These toxins are either naturally dissolved or are injected during water treatments and/or the transportation process by pipelines and faucets. They can also be caused by chemical residues from detergents, paints, inks, and gasoline such as Methyl Tertiary Butyl Ether (MTBE).

If the foul taste or odor is limited to your water heater, try flushing it and/or replacing the anode rod. This will typically fix the problem.

Alternatively, you can use hydrogen peroxide to flush the tank and disinfect the anode rod. This will also remove any mineral deposits that are causing the odor. It is important to note, however, that removing anodes from your water heater can greatly speed up the degradation and rusting of the appliance and should not be done unless it is absolutely necessary.